- Yamaha 2008 WR250X Owner's Manual
- Cyclepedia Yamaha WR 250R WR250X Waterpump Seal Bearing Replacement
- 2008-2010 Yamaha WR250R WR250X Service Repair Manual
- Yamaha WR250R (2008-2012) / WR250X (2008-2012) Service Manual by Cyclepedia Press LLC
- 2008 yamaha wr250x service manual
- Service Manual Table of Contents
- Get the right manuals, Keep Your Vehicle Running Smoothly
- We Also Recommend
- Yamaha WR250R WR250X Printed Motorcycle Service Manual by Cyclepedia
Show quick links.
Hide Hide permanently. Table of Contents. Troubleshooting Troubleshooting 85 Troubleshooting charts Page 2 EAU Read this manual carefully before operating this vehicle.
This manual should stay with this vehicle if it is sold. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Any reprinting or unauthorized use without the written permission of Yamaha Motor Co. Printed in Japan. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle.
If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer. Prima di usare il veicolo, leggete il manuale di istruzioni.
Yamaha 2008 WR250X Owner's Manual
Lesen Sie die Bedienungsanleitung bevor Sie dieses Fahrzeug fahren. Failure to Many accidents involve inexperi- Be a Responsible Owner inspect or maintain the vehicle properly enced operators. Always signal before turning or Always wear an approved helmet.
Carbon Monoxide is a colorless, odor- changing lanes. Make sure that Wear a face shield or goggles.
Page 14 Yamaha accessories, which are avail- of the motorcycle is changed. To avoid to minimize imbalance or instabili- able only from a Yamaha dealer, have the possibility of an accident, use ex- been designed, tested, and approved treme caution when adding cargo or Shifting weights can create a sud- by Yamaha for use on your vehicle.
Installing aftermarket prod- lightweight as possible and Aftermarket Tires and Rims ucts or having other modifications per- should be kept to a minimum.
Front fork rebound damping force adjusting screw page 8.
Cyclepedia Yamaha WR 250R WR250X Waterpump Seal Bearing Replacement
Helmet holder page 2. Fuse box page 9. Front fork compression damping force adjusting screw page 3.
Coolant reservoir page 4. Shock absorber assembly compression damping force adjusting screw page 5. Rear brake light switch page 4.
2008-2010 Yamaha WR250R WR250X Service Repair Manual
Engine oil level check window page 6. Clutch lever page 2. Left handlebar switches page 3. Multi-function display page 5. Right handlebar switches page 6. Brake lever page 7. Throttle grip page 8. The key can be removed. Otherwise the electrical systems will be switched off, which may result in loss of control or an accident.
Yamaha WR250R (2008-2012) / WR250X (2008-2012) Service Manual by Cyclepedia Press LLC
Page Indicator And Warning Lights 4. If the fuel level warning light comes on while riding in the measurement mode, change to the basic mode and push the 1. When the vehicle starts moving, cerning the use of this meter, please the stopwatch will start counting.
The stopwatch will continue counting 3. EAU Handlebar switches tripmeter 1. Check that the stopwatch mea- Left surement is in operation.
Shift pedal 1. Brake lever 1. Brake pedal The shift pedal is located on the left The brake lever is located at the right The brake pedal is on the right side of side of the engine and is used in com- handlebar grip.
Gasoline and gasoline vapors are extremely flammable. Page 30 Gasoline is poisonous and can as well as to the exhaust system. Handle gaso- Your Yamaha engine has been de- line with care. Never siphon gaso- signed to use premium unleaded gaso- line by mouth.
2008 yamaha wr250x service manual
If you should swallow This model is equipped with a catalytic converter in the exhaust system. This front fork is equipped with rebound damping force adjusting screws and compression damping force adjusting 1. Remove the rubber cap by pulling it out of the front fork leg.
Compression damping force adjusting screw 1. Rebound damping force adjusting screw To increase the rebound damping force Compression damping setting: 1. To obtain a precise adjustment, EAU should be no weight on the front end of Front fork bleeding it would be advisable to check the num- the vehicle.
This system boosts engine gas. Read and understand the fol Therefore, check this system regularly as described below and have a Yamaha dealer re- Move the sidestand down. If a malfunction is noted, have a Yamaha 2. Page For Your Safety - Pre-operation Checks Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in this manual, have the vehicle inspected by a Yamaha dealer. Before using this vehicle, check the following points Page 40 Adjust if necessary. Make sure that operation is smooth.
Service Manual Table of Contents
Check cable free play. Throttle grip , If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing. Control cables Lubricate if necessary. Page 41 Make sure that all nuts, bolts and screws are properly tightened.
Chassis fasteners — Tighten if necessary. Instruments, lights, signals Check operation. Check operation of ignition circuit cut-off system.
Get the right manuals, Keep Your Vehicle Running Smoothly
Sidestand switch If system is not working correctly, have Yamaha dealer check vehicle. The transmission is in the neutral gine in case of a turnover. In this EWA position. If not, ask a Yamaha dealer to coast for long periods of time check the electrical circuit.
We Also Recommend
Start the engine by pushing the tow the motorcycle for long dis- start switch. Page Tips For Reducing Fuel Consumption Shift up swiftly, and avoid high en- Since the engine is brand new, do not immediately have a Yamaha dealer gine speeds during acceleration.
Page Periodic Maintenance And Adjustment If If you do not have the tools or experi- you are not familiar with vehicle ser- ence required for a particular job, have vice, have a Yamaha dealer perform a Yamaha dealer perform it for you.
Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical skills. Drive chain Adjust and lubricate chain with a Every km mi and after washing the motorcycle or riding in the rain special O-ring chain lubricant Hydraulic brake service Regularly check and, if necessary, correct the brake fluid level.
Every two years replace the internal components of the brake master cylinders and calipers, and change the brake fluid. Remove the bolts and collars.
Yamaha WR250R WR250X Printed Motorcycle Service Manual by Cyclepedia
Removing and installing panels The panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. Place the panel in the original po- sition, and then install the collars To remove the panel and bolts.
Remove the bolts.