Table of Contents. The "Software Start Guide" is included at the end of this.
This manual is for the EOS 7D installed with firmware version. Show quick links. Hide Hide permanently. Digital photo professional 3. Imagebrowser 6.
Eos utility 2. Page 2: Introduction After shooting, playback and check whether the image has been properly recorded. If the camera or memory card is faulty and the images cannot be recorded or downloaded to a computer, Canon cannot be held liable for any loss or inconvenience caused.
If anything is missing, contact your dealer. Introduction Camera basics.
Canon EOS 7D Instruction Manual
Getting Started Basic Shooting Fully automatic shooting. Fn I : Exposure Fn II : Image Wipe off any water droplets with a dry cloth.
If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth. Dead pixels displaying only black or red, etc. Attach the lens. For other lenses, align it with the red index. Focus the subject. Press the shutter button halfway, and the camera will focus the subject.
EOS 7D DSLR Support
Page Nomenclature Nomenclature For detailed information, reference page numbers are provided in parentheses p. F : Bulb p. Page 21 Nomenclature Lens Lens with a distance scale Focus mode switch p. For connection to a supply not in the U. Page Getting Started Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations.
Attach the battery. Recharge the battery. Page 25 Charging the Battery Tips for Using the Battery and Charger Recharge the battery on the day before or on the day it is to be used.
Open the battery compartment cover.
Set to this position when not using the camera. Installing the Card Open the cover. Access lamp Remove the card.
Press the card ejection button. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus slightly.
Canon EOS 7D Mark II Key Features:
Detaching the Lens While pressing the lens release button, turn the lens as shown by You can press the shutter button halfway. Then you can further press the shutter button completely.
Pressing halfway This activates autofocusing and automatic exposure metering that sets the shutter speed and aperture. The exposure setting shutter speed and aperture is displayed on the LCD panel and in the viewfinder 0.
When you press a button, its function remains selected for 6 seconds 9. When the function turns off or if you press the shutter button halfway, the camera will be ready to shoot. This is called the Quick Control screen. Display the Quick Control screen. Select a tab. Set the desired language.
Follow steps 2 to 5 to set the current date, time, and time zone. Page 44 Before You Start Set the daylight saving time. Set if necessary. Page Formatting The Card Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or personal computer, formatting the card with the camera is recommended.
When the card is formatted, all images and data in the card will be erased.
If you do not want the camera to turn off automatically, set this to [Off]. After the power turns off, you can turn on the camera again by pressing the shutter button or other button. Select [Clear all camera settings]. Select [OK]. Highlight alert Disable Silent shooting Mode The grid is displayed in the viewfinder, and the electronic level is displayed on the LCD monitor. Displaying the Grid Select [VF grid display].
Display the electronic level. Also, to prevent botched pictures due to mistaken operations, major shooting settings cannot be changed in the fully-automatic modes. Aim the center of the Area AF frame over an area having good contrast, then press the shutter button halfway p. If you are too close to the subject, move away and try again. Page Full Auto Techniques 1 Full Auto Techniques Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective.
You can then recompose the shot and press the shutter button completely to take the picture. Page 57 C Creative Auto Shooting 4 Image effects Besides the standard image effect, you can set it for portraits, landscapes, or black-and-white photos. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. Select [Review time]. Three RAW recording quality settings are provided: 1, 41, and 61 p.
Canon EOS 7D Key Features:
Select [Quality]. The maximum burst applies to high-speed continuous shooting. It is recorded to the card as is, and you can select the quality as follows: 1, 41, or A 1 image can be processed with [3 RAW image processing] menu p.
Set the ISO speed. As indicated below, the ISO speed will be set automatically to suit the shooting mode. For natural colors and subdued images.
Beginners Guide to the Canon EOS 7D Part 1
U Faithful This Picture Style is for users who prefer to process images with their computer. To see the resulting effects, take test shots. To customize [Monochrome], see the next page. Select a Picture Style. Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explained on the preceding You can create Picture Styles whose parameter settings such as for sharpness and contrast are different.
Canon 7d user manual pdf
The Picture Style selection screen will then reappear. Do this procedure under the actual light source to be used.
Photograph a white object. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter.
Canon EOS 7D Mark II DSLR User Manual, Instruction Manual, User Guide (PDF)
Each color can be corrected to one of nine levels. This is for advanced users who are familiar with using color temperature conversion or color compensating filters. Page Auto Lighting Optimizer Auto Lighting OptimizerN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically.
With JPEG images, the correction is done when the image is captured. The default setting is [Standard]. Page Lens Peripheral Illumination Correction Lens Peripheral Illumination Correction Due to the lens characteristics, the four corners of the picture might look darker. This is called lens light fall-off or drop in peripheral illumination.