Instruction Manual. Table of Contents.
EverFocus M Instruction Manual 84 pages. Digital video recorder administrators guide and operting instructions edr 72 pages. Everfocus digital video recorder operating instructions edr 61 pages.
Page 2 All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the Everfocus Electronics Corporation. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Page 6 Note: This equipment has been tested and found to comply with the limits for a Class A digital device, Page 9: Safety Precautions Safety Precautions Refer all work related to the installation of this product to qualified service personnel or system installers.
Do not block the ventilation opening or slots on the cover. Do not drop metallic parts through slots.
This could permanently damage the appliance. Page 10 Safety Precautions Read Instruction All the safety and operating instructions should be read before the unit is operated. Retain Instructions The safety and operating instructions should be retained for future reference.
Heed Warnings All warnings on the unit and in the operating instructions should be adhered to. Follow Instructions All operating and use instructions should be followed. Page Product Overview Chapter 1. Highly efficient compression technology and superior resolution of recorded images make the Digital Video Recorder stand out from the competition as the best choice for security surveillance. Page 14 FULL: Press this key and channel Key at the same time to switch to full screen in both live mode and play back mode.
ZOOM: In full screen mode, 2x electronic zoom. Audio OUT: Connect an audio output to a monitor or other device. Remote Remote Control: Remote control port allows for an extension wire with an IR receiver instead of the IR receiver on the front panel. Page Monitor Display The status information of the cameras or machine will show up, and be located at different places on the screen. Channel tag 2. Event sign 3. Select sign 4.
Play status bar 5. Record status bar For mobile model only: 6. Page 20 Channel tag: A channel tag indicates the channel name of the screen. Event sign: Event signals which are small icons with a capital letter and red background show the events on each screen.
There are a total of 6 different signals: Alarm event. Play date The date on which the video was recorded. Page Installation Chapter 2. Installation The installations described below should be done by qualified service personnel or system installers.
Note: Monitor and Camera must be purchased separately. Page Basic Wiring Instructions Please refer to diagram 2. Power Connect the power source or adapter into the power socket. Cameras Connect each cameras video output to the video inputs on the digital video recorder.
Note: At least one camera must be connected before the system is running for the auto detection of video standard to take effect. Page 25 8.
Call Monitors Connect the call monitor output connectors to a call monitor. The call monitor display selected live cameras in full screen format. Note: The call monitor will only display one full screen camera at a time. Page Hard Disk Drive Installation The first step in installing the hard drive is to insert the hard drive sleeve into the machine.
The hard disk drive default setting is initially set to master. The second step is to insert the key provided and turn the tray key to the lock position.
The DVR can be mounted horizontally suspend or support mounted. Page 28 Unpack Everything Make sure you have everything you need before you begin the installation. Equipment Required The following tools may help you to complete the installation: Drill Screwdrivers Wire cutters Choosing the Location Choose a location for installation that: Provides convenient access for installing or removing the hard drive Allows air to flow around the fan vents.
Other camera s can also be installed in different locations for example, use the waterproof camera to the outside of vehicle. For installation procedure, please refer to the guide that came with the camera s you purchased. Page Dvr Menu Setup Chapter 3. DVR Menu Setup Assuming you have completed the first two chapters of this manual, you are now ready to begin setting up the digital video recorder.
This menu is used to set up the correct time and date for your region of the world. You are able to setup daylight savings as well as synch it with an internet based time server. Page 34 5.
This feature must be disabled in order to make any changes to the start and end times. Page 35 8. Page Camera Setup Menu Diagram 3. Page 38 4.
The first number is for sequence on the Main Monitor, the second number is for sequence on Call Monitor. There are six different qualities available. A higher image quality uses more HDD space. Page 39 6. Page 40 7. The table is for checking camera overall statuses only, not for changing them. Page Record Setup Menu Diagram 3.
Everfocus EDR810H Manuals
This menu is for setting up the options for recording. NO: Audio will not be recorded when machine is recording. Page 42 4. OFF: No watermark. The resolutions for PAL are x, x and x; the default value is x Page Alarm Setup Menu Diagram 3.
An alarm is defined as an electrical, electronic, or mechanical device that sends an alert by means of a signal. In this case the signal triggers the recorder to start recording the alarmed event. This menu contains all the alarm operations and options needed to successfully set up an alarm recording. Page 44 3.
EverFocus EDR810H Instruction Manual
For example if you had an external motion detector on camera one you would set this option to camera one. Page 45 NO: Disable alarm network. Page Motion Setup Menu Diagram 3.
We define motion as a change of pixilation in the field of view, which is detected by the digital video recorder, and triggering the recorder to start recording. Motion is also considered an event.
This menu is for setting up the digital recorder for motion recording on a per camera basis.
Edr 810 manual high school
Page 47 4. The default value is 5 seconds. In the motion edit mode: The default motion area of each camera is entire screen which displays in light green. Page Videoloss Setup Menu Diagram 3.
Usually it happens when the camera loses power or the camera fails. Page 50 5.
Moxa EDR 810 Series
Page Network Setup Menu Diagram 3. This menu is for setting up the configurations for networking to the DVR.