Fastiron Edge X424 Manual Arts

This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the cookie policy. By closing this banner, you agree to the use of cookies. Page of 94 Go.

Foundry FastIron Stackable.

Brocade FastIron Edge X X424 - switch - 24 ports - managed - desktop Series Specs

Table of Contents. Foundry networks edgelron installation guide 66 pages. Foundry network device installation guide 66 pages.

Page 2 You are not permitted to use these Marks without the prior written consent of Foundry or such appropriate third party. Page 3: Table Of Contents Each term refers to a specific set of devices, as shown in Table 1. Page 9: Audience Foundry Security Guide — provides procedures for securing management access to Foundry devices and for protecting against Denial of Service DoS attacks.

FESX424-PREM Fastiron Edge Switch

How to Get Help Foundry Networks technical support will ensure that the fast and easy access that you have come to expect from your Foundry Networks products will be maintained. Page Software Features Ethernet cable, power is continuous, even in the event of a power failure.

Figure 2. For example, you can use ports 1 —4 of the Gigabit Copper ports or ports 1F — Page 19 Copper port 10 or Fiber port 10, but not both at the same time.

You can use a combination of fiber and copper ports or all copper or all fiber ports, as needed. On the FES, if you attach both the copper and fiber connectors for a port to the network, the fiber connector takes precedence over the copper connector and will be the active connector for the port.

Table 2.

How to configure Layer 3 Switch using Vlan's

Page 23 The port is enabled, a power-consuming port device has been detected, and the module is supplying power to the device. Right for lower port The port is not providing in-line power. For a few features, including trunk group configuration and port monitoring, you will need to know the region to which a port belongs. Page Power Supplies The following sections provide further details about the power supplies for the FastIron family of switches. Page 29 Figure 2.

Page T Hresholds If desired, you can change the settings of the temperature thresholds associated with fan speed switches.

Applicable To The Following Products

June This chapter contains the following topics: Table 3. Details for each of the steps highlighted below are provided in this chapter and in the following chapter.

Bieber mystery sonatas pdf creator

Page Installing A Dc Power Supply The power supply is right-side up when the power connector is on the left and the fan vent is on the right. Press the two latches near the edges of the supply outward to lock the supply in place. If necessary, replace the power supply locking screw.

Technical Documents

After the power supply is properly inserted, connect the power source to the wires to activate the circuit. Page Wall Mount Installation If the links on these cables are good and the connected device is powered on, the link LEDs will light. The power supplies themselves do not have LEDs.

At this level, you can view some system information but you cannot configure system or port parameters. You can perform tasks such as manage files on the flash module, save the system configuration to flash, and clear caches at this level. In the above example, you could enter ip address Figure 4. Consequently, a crossover cable may not be required; a straight-through cable may work as well.

Table 4. Traceroute requests display all responses to a given TTL.

Eletromagnetismo aplicado wentworth pdf converter

This poll rate is controlled by the chassis poll time, which also controls how often the software polls other system components. However, Foundry Networks recommends that you disconnect the power supply from AC power before installing or removing the supply.

The device can be running while a power supply is being installed or removed, but the power supply itself should not be connected to a power source. Page Dc Power Supplies for a list of which power supplies are supported in which devices, and for illustrations of power supply placement in the Foundry devices.

Loosen the three screws used to hold the wires in the connector, then pull out the wires.

Fastiron edge x424 manual arts

Page Verifying Proper Operation OK — The power supply is functioning properly and supplying power to the chassis and installed modules. The 1-port and 2-port Gigabit Ethernet modules are optional. This chapter contains the following information: Table 7. Page Chassis Specifications The following sections present the hardware specifications for the FastIron Stackable devices.

FastIron Edge X-Series EOL Notice

Physical Dimensions Table 7. Table 7.

However, terminal connections will vary, requiring a cable with either a DB-9 or DB connector, male or female. Page Key Features All power supplies are auto-sensing and auto-switching.

Physical Dimensions and Weight Table 7.

Refer servicing to qualified personnel. Page Appendix 8 Cautions And Warnings Otherwise, the power supply or the device could be damaged as a result. Page 89 Never leave tools inside the chassis. If you run the chassis with an uncovered slot, the system will overheat. Page 93 Netzteils laufen. Nur das Netzteil sollte nicht an eine Stromquelle angeschlossen sein.

The fan may still be spinning at a high speed. Comments to this Manuals Your Name:. Enter text from picture:.

Foundry Networks FES Installation Manual

Latest comments:. Print page 1 Print document 94 pages. Cancel Delete. Sign in OR. Don't have an account? Sign up! Restore password.