Fx 890 Epson Manual Workforce

Fx 890 epson manual workforce

This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy.

If you want to know more or withdraw your consent to all or some of the cookies, please refer to the cookie policy. By closing this banner, you agree to the use of cookies.

Fx 890 epson manual workforce

Most useful pages: More Printing position problems. Page of Go.

Page 61 Page 62 - Accessing the printer driver from the St Page Page Page - Loading paper in the high-capacity cut-s Page Page Page - Assembling the double-bin cut-sheet feed Page - Selecting the paper path bin 1 or bin User's Guide.

Show quick links. Hide Hide permanently. Table of Contents. Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Page 5 Uninstalling the Printer Software Page 6 Before Contacting Epson Page 7 Genuine Epson ribbon cartridge Start Here paper manual Provides information on setting up the printer and installing the software. User's Guide this manual Provides overall information and instructions on using the printer.

Cautions must be observed to avoid damage to your equipment.

Notes contain important information and useful tips on the operation of your printer. An interruption in power can erase information in the memory of your printer or computer. Also avoid outlets on the same circuit as large motors or other appliances that can cause voltage fluctuations. Paper can be fed into the printer from the front, bottom, or rear. Select the paper source that best suits your current printing needs. If you print on thick paper such as multipart forms, use the front paper slot because this paper path is almost straight.

This reduces the chances of paper jams. The table below describes each paper release lever position. Turn off the printer and open the printer cover. The paper-thickness lever is located on the left side of the printer.

FX-890 Epson Printer Parts

The numbers next to the lever indicate the thickness setting. Use the table below to select the appropriate paper thickness.

Fx 890 epson manual workforce

Positioning your continuous paper supply When you load continuous paper, make sure you align your paper supply with the tractor so the paper feeds smoothly into the printer, as shown below. Make sure the tractor is installed in the rear push position and the sheet guide is removed from the printer.

Set the paper release lever to the rear push tractor position. Release the left and right sprockets by pulling the blue sprocket lock levers forward. Slide the right sprocket illustration shown below approximately 12 mm 0.

Then slide the another sprocket to match the width of your paper, but do not lock it. Page 25 Note: For your safety, Epson recommends operating the printer with the printer cover closed. The printer will function with the printer cover opened or removed, but maximum safety and print speed are achieved when the cover is closed. Using the tractor in the front push position Installing the tractor in the front push position Before installing the tractor in the front push position, remove it from its current position.

Set the paper release lever to the front push tractor position.

Uni en 517 pdf merge

Insert the paper into the bottom slot as shown in the illustration below. Make sure your paper has a clean, straight edge. Then open both sprocket covers and fit the first four holes of the paper, with printable side up, over the tractor pins. Then close the sprocket covers. Close the front cover. Using the tractor in the pull position Using the tractor in the pull position is ideal for printing on thick and heavy continuous paper, such as multipart forms or continuous paper with labels.

Troubleshooting

However, you cannot use the tear-off function with the pull tractor. Make sure the printer is turned off. Then open the paper guide cover by pulling its back edge forward. Lift the printer cover and pull it straight up. Press the tabs on each side of the paper tension unit upward and pull it towards you.

Epson FX-890II User Manual

Store the paper tension unit in a safe place. Attach the sheet guide if necessary then lay it flat on the printer.

Valsa brasileira pdf to word

Then slide the edge guides to the middle of the sheet guide. Before loading a paper, make sure the following: - the printer is turned off - the printer cover is removed - the tractor is installed in the pull position - the sheet guide is lying flat on the printer 2. Slide the left sprocket approximately 12 mm 0.

Epson FX 890 - B/W Dot-matrix Printer Manuals

Then slide the right sprocket to match the width of your paper, but do not lock it. Bottom slot: Load paper in the bottom slot with the printable side facing up. Fit four holes of the paper over the tractor pins on both sprockets. Slide the edge guides on the sheet guide to the center.

Fx 890 epson manual workforce

Close the front cover as shown below. Note: When using the bottom slot, you do not need to open the front cover. Turn on the printer. Then open the paper guide cover by pulling its back edge toward you. To reduce paper jams and improve continuous paper feeding, you can install the optional pull tractor unit. Page 41 Attach the printer cover. Make sure the sheet guide is installed and lying flat on the printer.

Note: For your safety, Epson recommends operating the printer with the printer cover closed. You can then easily tear off the printed document.

You can also load single-sheet paper using an optional cut-sheet feeder and sheet guide. Page Using The Sheet Guide You can use the supplied sheet guide to load one single sheet, multipart forms, or envelopes at a time from the rear of the printer.

Your single-sheet paper can be up to mm Follow these steps: Caution: Do not load labels or envelopes in the front sheet guide. Slide the paper printable side up between the edge guides until it meets resistance.

Clearance de creatinina valores normales pdf to jpg

The printer loads the paper automatically. Set the paper-thickness lever located under the printer cover to 0 if you are using ordinary single-sheet paper. Also move the paper release lever to the single-sheet position.

Epson FX 890 Manuals

Turn on the printer, if necessary. Slide the left edge guide until it locks in place next to the triangle mark on the sheet guide. Then, adjust the right edge guide to match the width of your paper. Page Loading Special Paper The printer feeds the paper automatically and is ready to print.

When fed backward, labels can easily peel off the backing sheet and cause a paper jam. Note: Envelopes can be loaded only in the rear paper slot.

How to print a self test on an Epson FX-890 dot matrix printer

Before loading cards, set the paper-thickness lever to position 2 and set the paper release lever to the single-sheet position. Set the paper release lever to the front or rear push position, depending on the tractor position you are using. Hold down the Pause button for about three seconds. The Pause light begins flashing and the printer enters the Micro Adjust mode. Page 58 5. After you set the top-of-form position, press the Pause button to save the adjusted setting.

EPSON Status Monitor 3 program allows you to monitor the status of your printer, alerts you when errors occur, and provides you with troubleshooting tips.

Fx 890 epson manual workforce

The instructions are the same all models. Click Preferences. These menus contain the printer driver settings. Printer Software To view a menu, click the corresponding tab at the top of the window.

Accessing the printer driver from the Start menu Follow these steps to access the printer driver from the Start menu: Note: The screen shots used in this procedure are from the Windows 10 operating system.