Graphtec Cutting Plotter Ce6000-60 Manually

Graphtec cutting plotter ce6000-60 manually

This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy.

If you want to know more or withdraw your consent to all or some of the cookies, please refer to the cookie policy. By closing this banner, you agree to the use of cookies. Page of Go.

Graphtec CE6000-60 Plus 24" Cutter

Page - Positioning of the Media and the Registr Page - Position of the Origin Point and the Reg Page - Adjusting for the Registration Mark Scan Page Page Page - Setting the registration mark automatic Show quick links. Hide Hide permanently. Table of Contents. Troubleshooting Chapter Troubleshooting Troubleshooting Cutting pro fc series cutting plotter pages.

Page 3 Use of the plotter in such a condition may result in a fire hazard or electric shock. Page 4 Use of a damaged cord may result in electric shock or a fire hazard due to current leakage.

Graphtec cutting plotter ce6000-60 manually

Unplug the power Prohibited cord from the socket Such action may impair its performance. Prohibited Prohibited Provide sufficient space around the plotter so that To ensure high cutting quality and optimal productivity, be sure to read this User's Manual thoroughly prior to use.

Handle the cutter blades and holders with care to prevent bodily injury. Cutter Blades Cutter blades are very sharp.

Write a Review

While handling a cutter blade or cutter pen, be careful to avoid cutting your fingers or other parts of your body. Be sure to observe all the cautions on the label. The use of a different stand may cause a plotter malfunction or bodily injury. GRAPHTEC is not responsible for any interference caused by using cables and connectors other than those recommended or by unauthorized changes or modifications to this equipment. Page Selecting A Power Cable Selecting a Power Cable Be sure to refer to the following tables if you wish to use a cable other than the one supplied as an accessory.

Graphtec cutting plotter ce6000-60 manually

Table 1. Page 12 Contents of Operation from Menu Screen Page 13 Positioning of the Media and the Registration Mark Position of the Origin Point and the Registration Mark USB Interface. Used to access various plotter functions. Push rollers Rollers that push the media against the grit rollers.

CE6000 Series

A tray to set media in. Roll-medium tray guide rail.. A rail to set the roll media tray in. Power switch Used to turn the plotter on and off. AC line inlet Inlet where the power cable is connected.

CE5000-60 & 120 Series

Media stocker A stock to set roll media in. Stock shaft A roller that takes in roll media. Page Assembling Assembling Assemble the stand.

The manual of detection summary of hamlet

The stand is made up of the following parts. People can be accidentally injured by the machine's edges. Please be very careful.

CURSO PLOTTER GRAPHTEC CE-6000

Please be careful not to get your hands pinched or stuck when you secure the machine. Page 25 3 Attach a media stocker to each of the left and right stand side bars with two socket head cap screws, using the Allen wrench.

GRAPHTEC CE6000 SERIES User Manual

Mount the media stockers so that each one of media stockers of long side to be rear side. Socket head cap screw Media stocker Media stocker Page 27 3 Attach a media stocker to each of the left and right stand sides with Five socket head cap screws, using the Allen wrench.

Mount the media stockers so that each one protrudes directly above the longer of the two stand foot lengths. Make sure the rollers on the roll media tray are on the outside on both sides. Roll-medium tray guide rail Roll-medium trays Page 29 Mounting CE 1 Set one stopper in the stock shaft.

Keep the stopper screws slightly loose.

Specifications

Stock shafts Stoppers 2 Slide the stock shaft into the media stocker. Stock shafts Roller Use the cables specified by Graphtec, matching the computer that is to be connected. This will be explained in CE Cutter Plunger Nomenclature The plotter cuts using a cutter blade mounted in a plunger. Page Blade Application And Features Blade Application and Features Referring to the blade application and features in the table below, select the optimal cutter blade and medium to be cut.

Blade part no.

Additional Instructions

Attaching a Tool When mounting the tool in the tool holder, please note the following. Page Removing The Tool 3 Make sure that the tool bracket is engaged on the tool's flange, and then tighten the screw. Flange Bracket to hold tool Removing the tool When removing the tool, turn it counterclockwise to remove the tool.

Ivan ilitch obras completas pdf to jpg

Load the media according to the instructions given for each type. Use the grit roller on the right side of the media looking from the front as a guide when setting it in the media sensor. Page 37 3 Pulled from the front, the roll media should be long enough so that its tip completely covers the sensor. If you pull it too long, wind the roll and adjust the length. Push roller Media sensor 4 Position the media and the push rollers to correspond with Supplement the width of the media.

Recommended Posts

Page 38 5 Pull the media taut to make sure that there is no slack in the conveyance path, and then raise the media set lever to lower the push rollers. Media set lever Create the same amount of slack in the media as will be used for the back of the machine.

Operation 1 Lower the media set lever to raise the push rollers. Push roller Media set lever Media sensor 2 Set the roll media on top of the stock shaft, and then insert the roll media into the stopper.

Page 40 3 Push the tip of the roll media forward from the back of the CE Make sure to pull it so that there is no slackening across the roll media's route.

Graphtec cutting plotter ce6000-60 manually

Page 41 5 Position the media and the push rollers to correspond with the width of the media. When the CE The push rollers push down on either side of the media.

Graphtec cutting plotter ce6000-60 manually

Use Supplement the grit roller position guide to make sure the push rollers are The media must always be positioned over set on top of the grit rollers. Page 42 When Feeding Long-axis Media at exceeds 2 meters Position the push rollers at least 15 mm inside the edges of the media.

Graphtec cutting plotter ce6000-60 manually

Push roller 15 mm 15 mm Media When Feeding Long-axis Media at least 2 meters Position the push rollers at least 5 mm inside the edges of the media. Page 43 8 When the set lever is up and the media is held down by the Supplement push rollers and the media stopper is unlocked, pull out the Dirt from the floor may stick to the media when roll media and give it slack.

Push roller Media set lever Media sensor 2 Set the sheet media so that the paper's edges line up with the guideline on the front side. Page 45 3 Position the media and the push rollers to correspond with Supplement the width of the media.

Graphtec cutting plotter ce6000-60 manually

The media must be at least mm in length. The push rollers push down on either side of the media. Use The media must always be positioned over the grit roller position guide to make sure the push rollers are the media sensor.

Push roller Media set lever Media sensor 2 Make sure that the sheet media completely covers the media sensor. Media sensor Page 47 3 Position the media and the push rollers to correspond with Supplement the width of the media. The media must always be positioned over Use the 3 push rollers to push down the sides and center of the media sensor. Page 48 5 You can set the media straight by stacking media you pull out and matching the edges up together. After you check to make sure there's no slack, raise the media set lever and fixate the sheet media in the push roller.

Media set lever Line up Media guide bar Aligning the Push Roller Position the left and right push rollers to correspond with the width of the media.