Hts-580 Series Total Station Manual

Hts-580 series total station manual

This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the cookie policy.

By closing this banner, you agree to the use of cookies. Page of Go. Page - Detaching the Trimble Robotic Holder fro Table of Contents. Page 2: Legal Notices All other trademarks are the property of their respective owners.

Much more than documents.

It applies to the Trimble S Series total stations. Page 3: Safety Information Safety Information For safety information please refer to the Trimble S Series regulatory information document delivered with the product.

Transport As an option the instrument can be equipped with a Locate 2 Protect L2P module that communicates via cellular technology, it is therefore necessary to check local regulations before transporting this instrument by air. Page 9: Welcome The S Series total station is available in several models and configurations. Trimble S Series Total Stations Page Your Comments Your feedback about the supporting documentation helps us to improve it with each revision. E-mail your comments to ReaderFeedback trimble.

Registration To receive information regarding updates and new products please register on the Trimble web site.

Hts-580 series total station manual

If started, with a battery with a flashing LED, the operating time will be between 5 and 15 minutes. Page Charging The Battery The battery is supplied partially charged.

Charge the battery completely before using it for the first time. Page 14 Conditioning a single battery can take up to 24 hours. Conditioning five batteries can take up to 60 hours.

Trimble recommends that you condition the battery or batteries on a weekend.

Inherit the wind book quiz format

Do not touch the bottom plate. Page Dual Slot Charger 2. Place the charger on a hard, flat and level surface, to ensure that there is airflow under the charger. The charger scans the slots for a battery. Page 16 Conditioning a single battery can take up to 24 hours. It is recommended that you condition the battery or batteries on a weekend. Page Connecting An Internal Battery 1.

Manual Total Stations

Open the battery compartment hatch by pressing the lock release button. Slide the battery into the battery compartment with the battery connectors positioned towards the top of the instrument.

Correct Setup and Operation of Trimble total station

See Figure 2. TIP — When connecting the cable to the instrument, keep the Trimble logo on the connector upward. Trimble logo Trimble recommends that you take some time to familiarize yourself with the names and the locations of the controls. An LED in the trigger key indicates if the instrument is turned on.

A solid light indicates on and a flashing light indicates suspend mode. Page Face 2 Display When a Trimble CU is attached to the instrument, the software running on the unit controls the face 2 display and keyboard, and determines which secondary functions are available.

For details on how the software controls the face 2 display, refer to the field software documentation.

LEARN MORE: OUR DIVISIONS

Page Optical Plummet The instrument handle is placed so that it will not obscure measurements in the face 1 position, or restrict plumbing vertically beneath an overhead marker or sighting up a vertical shaft. Page 23 1. Unscrew the two Torx screws securing the handle to the instrument, use a T30 Torx key.

Slide the handle horizontally away from the front of the instrument. Page 24 Detaching the instrument handle Attaching the handle: Attaching the handle is completed by reversing the above operations.

Page Setup 2.

Any high quality tripod and tribrach can be used. However, Trimble strongly recommends the use of tripod heads made of steel, aluminum or similar material.

Hts-580 series total station manual

Tripod heads of fiberglass or other composite materials are not recommended. Page Starting The Instrument 2 keyboard and display are pointing towards you. The face 2 display menus described in this chapter can only be accessed when there is no Trimble CU attached, please remove the Trimble CU before starting the instrument. Page 31 1. Press to change the digit to the correct number. Press to select the next digit.

EXPLORE HEXAGON

When all four digits have been set to the correct PIN code press C. This means that the PIN Code security will be inactivated. A document with the PUK Code is supplied to the user when the instrument is delivered. Please save this document in a safe place. NOTE — To change the radio channel number press to select and then press to change the Next channel number in the display.

Hts-580 series total station manual

Page 35 5. If you want to cancel Press to select and then press to return to the Cancel Radio Settings menu. Page 36 4.

Trimble S Series User Manual

When you have found the network ID number of your choice press to select and then press to store this network ID number. You will then be returned to the Radio Settings menu. Page Bluetooth Device Settings Bluetooth wireless technology option in the instrument.

This is carried out as follows. Page 38 NOTE — To reduce power consumption and extend operation time, Trimble recommends that the Bluetooth device is switched off when not in use. Page Reference Ha To calibrate the compensator, the instrument needs to be in perfect balance.

Hts-580 series total station manual

After calibration the compensator sensor will automatically adjust and allow for changes in that balance caused by the presence of a Trimble CU controller or the absence of an internal battery.

Page 40 Figure 3.

Total Station

NOTE — Trimble recommends that you regularly carry out a compensator calibration, particularly when measuring during high temperature variations and where the highest measurement accuracy is required.

The calibration process involves the instrument automatically reading the compensator value at a series of predetermined positions through the full rotation of the instrument. Trimble also recommends that the operator keep a record of the dates and values measured so that any gross changes can easily be detected. Gross changes can indicate the need for a check by an approved service center.

Hts-580 series total station manual

Page 43 Then press to continue to Trunnion collimation. Trunnion — correction. Then press to accept and store the new collimation values. Store — Cancel.

Uploaded by

Then press to return to the menu. Page 44 Aim accurately in face 2 towards a point at least 15 grads Press to measure and record angles.

Page 45 Perform the test over a similar distance as that you will be working on, but at least m. The prism target must be very still during the test Trimble recommends that you use a tripod or bi-pod mount for the target and must be in clear line of sight without any obstructing traffic. Page 46 The laser pointer is mechanically aligned to the telescope cross hairs.

Hts-580 series total station manual

The laser may require periodic adjustment to keep it perfectly aligned for measurement. Page 47 With the laser pointer on, you can adjust the beam, For more information, see The Laser Pointer, page Autofocus calibration The instrument is equipped with an autofocus function.

Before you can start using the autofocus, the function needs to be calibrated.

A rocking horse winner pdf writer

Page 48 1. To return to the menu, press to scroll to Setup Back Radio settings Compensator calib. Tracker collim. Page Firmware Version Information Face 2 display. Press to scroll to Select language 2.

Press to scroll through the available languages. Press to set language. The laser pointer is coaxial with the line of sight of the telescope.

Page 51 3. If the red laser spot lies outside the cross-hairs, adjust the direction of the beam until it matches the cross-hairs, see Figure 3.

Figure 3. To correct the vertical position of the laser spot, insert the Allen key into the access hole for the vertical adjustment screw and turn it as shown in figure 3.