DIGITECH GNX4 Owner's Manual
Hide Hide permanently. Table of Contents. Digitech guitar multi-effects processors pages. Automatically generates bass and drum parts that match your song 63 pages. Page 6 Warranty We at DigiTech are very proud of our products and back-up each one we sell with the following warranty: 1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty. DigiTech warrants this product, when used solely within the U.
Digitech GNX4 Manuals
Page 9 Re-Amping a Guitar Track Page Introduction However, if you find anything missing, please contact the factory at once. Please take a moment to fill out the warranty card.
It is your safeguard in the unlikely event that the GNX4 develops a problem. The switch is located to the right of the XLR jacks on the rear panel. Page 14 The Effects Matrix displays the effects parameters available for editing in each preset.
Displays The Displays give feedback of the various functions that are being used in the GNX4, including preset name, editing functions, tuner, utility menus, drum machine and recorder settings.
Page The Rear Panel 6. Page 18 Page 20 Audio Routing Setups - All input sources guitar, mic, line, drums, onboard 8-track recorder playback and USB playback are routed to both output pairs in mono. Page Mic And Line Setups The Mic and Line Setups are configurations for the mic and line inputs designed for both live performance and recording applications. For many GNX4 users, its primary purpose will be for use in live performances.
Whether you are a solo performer who spends weekends playing at a small club or the power-user playing the largest venues each night, the GNX4 has just what you need to do the gig right.
To adjust your microphone input level for optimal use see Optimizing the Page Computer Recording Application 1. To adjust your microphone input level for optimal use see Optimizing the Mic Input Level on page Page Applying Power 2.
Footswitches turn the effects on and off. Footswitch 5 is used as a Tap-Tempo switch for setting the delay time during a live performance. Press Footswitches 3 and 4 simultaneously to access the Tuner. The display briefly flashes.
To begin tuning, play a note on your guitar a harmonic at the 12th fret usually works best. The red numeric display shows the note being played, They are located to the left of the Status Button. The sound that you hear while adjusting these parameters will depend on the channel status see chart below. Your choices include Amp channels 1 and 2 have selectable amps and cabinets.
Each channel has independent controls for gain, level, EQ, and cabinet tuning. The procedure for selecting Amps or Cabinets is as follows: 1. Page Storing Amp Parameter Edits 4. Repeat steps 2 and 3 you have finished naming the new HyperModel. Effects placed post amp are those that typically sound best when heard in stereo like modulation effects, delay and reverb.
Preset Levels The GNX4 presets each have an independent level control for quick balancing of the levels between presets.
Ratio settings are: 1. As you speak into the microphone, your instrument mimics what you say. There are five Talker types. Page Stomp Box Modeling Talker will have trouble tracking.
If the input is too strong, the Talker will clip making the words unintelligible. See Optimizing the Mic Input Level on page 13 for more information regarding mic level adjustment. The mic level sensitivity ranges are from Page Noise Gate A Noise Gate is designed to eliminate hiss and ambient noise while you are not playing.
A Noise Gate can also be used to create an automatic swell in volume. Page Flanger Effects and Parameters Flanger A Flanger uses the same principle as a Chorus but has a shorter delay time and adds regeneration or repeats to the modulating delay.
This results in an exaggerated up and down sweeping motion to the effect.
DIGITECH GNX2 User Manual
Ranges from bottom of the sweep point to top of the sweep point. Mod Mix - Knob 5 controls the mix of wet and dry signal. Ranges from all dry to all wet. Page Autoya all wet. It makes your guitar appear to speak based upon the dynamics of your playing style. Parameter 1 - Knob 2 adjusts the Attack of the synthesized voice.
Ranges from Parameter 2 - Knob 3 adjusts the Release of the synthesized voice. Page Detune that turns off the input to the Delay and lets you play over the top of a passage in the Delay loop.
Reverb Type - Knob 1 selects the type of Reverb or acoustic environment. Each parameter assigned to the Expression Pedal can have specific ranges of how much the parameter is controlled by using the minimum and maximum controls.
However, you can configure the function of the Amp Channel Footswitch within a preset. Page Lfos A minimum and maximum value can be assigned. For instance: if the Amp Gain was assigned to LFO1, and the minimum value was set at 1 and the maximum value was set at 99, the GNX4 would automatically sweep the amount of distortion from clean to distorted and back to clean. Individual LFO speeds can also be assigned.
Page Creating A Preset HyperModel with a preset that gives your single coil pickup a humbucker sound, uses no Compression, has a Noise Gate that opens quickly, a subtle Chorus effect, no Delay, and a little bit of a Hall reverb. The following guide steps you through the process of creating just that preset in the GNX4. Selecting a Preset The first step to create a custom preset of your own is to select a starting point.
Therefore, you may want to change the settings. To access the Parameters for Channel 1, do the following: 1.
The display briefly reads Amp Saved and then returns to the name of the selected preset. Page Adjust The Noise Gate 1.
If we changed presets or turned the GNX4 off without storing these settings, it would forget what we had done and revert back to the original preset. Bank Down Footswitch - Selects the previous bank of presets.
Pressing and holding this footswitch scrolls down through banks. Preset Down Footswitch - Selects the previous preset. Pressing and holding this footswitch scrolls down through presets. Page Footswitch Operation not on a Compact Flash card. It also has a MIDI input. Each of these inputs can be used to record audio and each has multiple different routing configurations available. Nothing is sent up the USB 4 channel. Path C taps the guitar signal at the output of the GNX4 and can include any effects processing that may be used.
Path C taps the signal at the output of the GNX4 and can include any effects processing that may be used.
Manual digitech gnx4 em portugues
Page The Gnx4's 8-track Recorder Since there is no onboard recording memory, you must first insert an optional Compact Flash CF memory card into the card slot on the rear panel to begin recording tracks.
The GNX4 supports most CF cards but obviously, the larger the card size, the more recording time is available. The GNX4 has eight individual tracks that can be recorded to. To select a pattern or file that you would like played back with a song, follow these steps: 1.
DIGITECH RP-10 Owner's Manual
For example, the 8th Beat pattern will display as 2. This tempo should be set before any audio is recorded if the Click Track or drum machine is to be used as a metronome during recording. Page Drum Kit MP3 is selected.
To select a Drum Kit, follow these steps: Begin with the recorder stopped. Page Pre-roll Pre-Roll can also be used as a count in cue, indicating when the very beginning of the song starts.
To setup the Pre-Roll function, follow these steps: Begin with the recorder stopped. Page Auto Stop Quantize function creates perfectly timed loops to the nearest eighth note of a given tempo.