Show quick links. Hide Hide permanently. Table of Contents. Page 2: Table Of Contents Advanced Page 3 Storage Page 4 Networking Basics Page 7: Hardware Features Press this button to turn the unit on or off. Power Receptor Receptor for the supplied power adapter.
Page Web-based Configuration Utility 4. Click Settings to configure your router. Click Continue. This screen gives you an overview of your Gateway including the Internet connection status, system information, local network information, and storage status.
Enable Button: Click the Enable button to turn on the wireless function. Page Settings Displays the wireless mode the Gateway is set to.
Network Select the authentication mode from the drop-down. Open System is the default settings. Step 3: Your newly added device will now be displayed in the list. Click the red X to remove the device from the list. To add more, repeat steps 1 and 2. Step 3: Allow minutes for the devices to communicate.
D-Link 2750B Wireless Gateway Router
Once complete your client will connect to the gateway. Algorithm: Group Key Update Enter the amount of time before the group key used for broadcast and multicast data is changed.
Hex - letters A-F and numbers are valid. ASCII - all letters and numbers are valid. Key Length: Select the level of encryption 40 or bit.
Need more support?
Page Server Port: Enter the port you want to use. Shared Secret: Enter the Shared Secret passphrase. Page Advanced The IP address of the computer or device. Subnet Mask: The subnet mask of the computer or device. Page Internet Internet settings. However, if you choose to do so, you must disable Auto- Sense by clicking the Stop Auto-Sense button from this page.
Note: Once you disable Auto-Sense, you can only re-enable it by restoring factory settings. Subnet Mask: The subnet mask of the Gateway.
Setup Asus DSL-N12E according the ISP Setting
Page 26 Received Packets: Amount of packets received. Sent Packets: Amount of packets sent.
QUICK SETUP GUIDE
Time Span: Displays the time connected. Page 28 Displays the connection type the Gateway is set to. New IP Range: Click to add a new entry. Page Routing The metric value assigned to this route.
Wireless N300 ADSL2+ Modem Router + USB
Status: Displays the status of the route. Page Bridging You can enter your own devices to add to the bridge filter table. Page Firewall Settings However, Medium security allows customization through NAT configuration so that you can enable the traffic that you want to pass.
Minimum Security Low security setting will allow all traffic except for known attacks. With Low security, your Low : Gateway is visible to other computers on the Internet. Schedule: Select Any or a user defined schedule. Select User Defined to create a schedule rule. New Entry: Click to add a new port forwarding rule refer to the next page.
Page 38 Step 5: The new rule will appear in the list. Use of this option is only recommended as a last resort. This will de-activate any port-forwarding rules. Enter the IP address of the computer you want to open to the Internet. Page Port Triggering Displays the outgoing port s and protocol s used by the application. Incoming Ports to Displays the incoming port s and protocol s opened by the application.
Open: Action: Click the red X to delete the rule. Action: Click the red X to delete the listing.
D-Link DSL-2750B Quick Setup Manual
Close: Click to go to the Overview page. Page Advanced Filtering Displays the outgoing port s and protocol s used by the application.
Page Remote Administration Web Management interface. The default port is Management: Diagnostic Tools: Check the box to activate the diagnostic tools rule. Page Security Log Click to save the log to your computer. Settings: Click to select filters for the information displayed in the log refer to the next page. Refresh: Click to update the log details on the screen so it displays any recent activity.
Page Settings Settings Check the box es below to include in the security log. Page System Log Click to update the log details on the screen so it displays any recent activity. Filters: Select specific items to record in the log or click New Filter to add an item.
Click Apply Filters to add it to the list. Page Services Services Overview This page displays the status of each service. Click on the service to configure. Select the profile that fits you the best and click OK. Page Utilization By Computer Utilization by Computer This screen displays bandwidth usage from computers on your local network.
Utilization by Application This screen displays bandwidth usage from applications on your local network.
Manual modem dsl 2750b setup
Rx Bandwidth: Select the Rx traffic bandwidth from the drop-down. Select Specify to enter your own value, Automatic, or Unlimited.
Click the pencil icon to edit the priority and settings for each DSCP value.
Select the queue for each You will be directed to the Filtering Policy page refer to the next page. You will have to connect to the Gateway from another computer or reset the Gateway back to factory default settings. Page 57 Enter specific websites you want to block or allow.
List of Keywords: Enter keywords that are on websites that you want to block or allow.
Click to save your policies. Created policies will then appear in the drop-down list when adding LAN computers. Page Advanced Options If a user from your local network attempts to visit a site that you blocked, they will get redirected to the URL you want. Page Statistics Statistics This page displays the number of allowed and blocked sites that were attempted to be view from your local network.
Page Storage Your drive will appear here. Click the name of the drive to access the folders and files. Advanced users can click New Entry to assign specific users, groups to specific folders on your USB drive. Click OK to save your settings.
Frequently asked questions
Page Disk Management A. If you uncheck this box, you can rename the partition storage area. Disks: Displays information about your USB drive. Click on the Name of the drive to access more information about the drive see below.
Also, click the name under Partitions to view the files on your drive. Page Ip Address Distribution dhcp Select Disable turn off option , Served to have the Gateway assign IP settings to only the devices in the list , or Denied to have the Gateway assign IP settings to all devices Control: except for the ones in the list.