Minidisc Sony Mds-je500 Manual Transmission

Minidisc sony mds-je500 manual transmission

Sony MDS-PC2 Operating Instructions Manual

This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance. You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Minidisc sony mds-je500 manual transmission

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:.

The model and serial numbers are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Minidisc sony mds-je500 manual transmission

Thank you for purchasing the Sony MiniDisc Deck. Before operating the deck, please read this manual thoroughly and retain it for future reference.

Focus on grammar 3 answer pdf printer

Z Indicates a procedure that requires use of the remote. Starting recording with six seconds of prestored audio data Time Machine Recording Synchro-recording with the audio component of your choice Music Synchro-recording This chapter describes the location and function of the various buttons, controls, and jacks on the deck and the supplied remote. Further details are provided on the pages indicated in the parentheses. Press to turn on the deck.

When you press the switch again, the deck turns off and the indicator lights up.

Minidisc sony mds-je500 manual transmission

Point the remote toward this sensor for remote operations. D MD insertion slot 14 Press to select the input jack or connector of the program source to be recorded. H REC z button 14 18 J YES button 18 27 30 39 K AMS control 12 14 23 30 39 Turn to locate tracks, set the clock, select the input characters, or select a menu item and a setting value. Press to locate a portion within a track, change the contents of a program, or change the input character. Set to OFF to turn off the timer.

Controls of Function and Location.

Sony MDS-JE530 Service Manual

SCAN button 24 Z. Press to insert a three-second blank space between tracks or to pause play after each track. HOLD button 17 Z. REC button 20 Z.

GB 6 Remote control description.

Sony MDS-JA333ES User Manual

Press to locate a portion within a track, change the contents of a program, or shift the cursor to the right. Lights when the MD is being controlled by an external device connected to the deck. B Disc name and track name indicators display. Displays disc and track names, Edit Menu parameters, and Setup Menu parameters etc. The track name appears instead of the disc name during play. D Recording and editing indicators. Lights when the deck is set to assign track numbers automatically during analog recording.

GB 8 Display window description.

Woronowicz alkoholizm jako choroba pdf creator

Shows all the track numbers within a grid if the MD is a premastered disc, or without a grid if the MD is a. If the total number of tracks exceeds 15, B appears to the right of number 15 in the music. The display format that you have selected in each of the deck statuses play, recording, etc. If you disconnect the AC power cord, however, all the displays will revert to their default i.

SONY MINIDISC DECK MDS-JE510, SONY MDS-JE500, SONY MDS-JE330 What's inside?

Total number of tracks, total recorded time and disc name 1. Controls of Function.

Sony MDS-JB940 User Manual

Connect a digital coaxial cable to input digital signals from other components. Connect a digital optical cable to input digital signals from other components. There is no distinction of IN1 and IN2 connectors.

This chapter provides information on the supplied accessories and hookups.

Minidisc sony mds-je500 manual transmission

Be sure to read this chapter thoroughly before you actually connect any equipment to the deck. GB 10 Before you start the hookup. When using the remote, point it at the remote sensor on the deck.

Under normal conditions, the batteries should last for about six months. When the remote no longer operates the deck, replace both batteries with new ones. Doing so may cause a malfunction. Started Getting.

Minidisc sony mds-je500 manual transmission

CD player, DBS tuner, etc. When connecting an audio connecting cord, be sure to match the color-coded pins to the appropriate jacks: white left to white and red right to red.

When you turn on the MD deck and there is no MD in the deck, demonstration mode is activated automatically after about ten minutes. To deactivate the demonstration mode, press any button on the deck or on the remote. To turn on the demonstration mode again, perform the same procedure described above. For USA and Canadian models, date is displayed in the order of month, day, year, and time on a hour clock.

For European model, date is displayed in the order of day, month, year, and time on a hour clock. The month or day indication stops flashing, and the day or month indication starts flashing. If this happens, reset the clock. This chapter explains the various ways to record to an MD, as well as how to mark track numbers and perform synchro-recording with other components.

Penelope neri sea jewel pdf

If the MD has been partially recorded, recording starts after the recorded tracks. If you want to record to a new MD or start recording from the end of the recorded portion, skip this step and go to step 6.

Turn AMS or press. Press X at the point you want to start recording from. The track number increases by one. For example, if you paused recording while recording track 4, the track number will be 5 when you resume recording.

To protect an MD recording, slide the record-protect tab in the direction of the arrow see illustration below to open the slot. To enable re-recording, close the slot. You cannot record over existing material when Shuffle Play page 27 or Program Play page 27 has been selected. MDs to Recording.

The indication stops flashing when the deck reaches the end of the recorded portion. The recording will be lost if you disconnect the AC power cord while the indication is on. The deck is updating the TOC. Do not disconnect the AC power cord or move the deck while the indication flashes. A built-in sampling rate converter automatically converts the sampling frequency of various digital sources to the In addition to normal stereo recording, this deck has two long time recording modes: LP2 and LP4.

When recording in LP2 Stereo mode, you can record 2 times the normal recordable time, and in LP4 Stereo mode, you can record 4 times the normal recordable time. In addition, the recordable time for monaural recording is approximately double the stereo recording time. In addition, you cannot perform S.

This indication is displayed when the track is played on a deck that does not support long-time recording page The MD LP indicator lights up when you press z in step 3 above. It is not displayed on decks that support MD LP mode. These MDs cannot be played back on other decks. The function freezes the peak level meters at the highest level reached by the input signal.

Therefore, if the output level of the connected component is low, it may not be possible to set the recording level to maximum. The deck can be set to automatically erase any blanks that are produced when the signal is interrupted during recording.

Minidisc sony mds-je500 manual transmission

The function that activates Smart Space or Auto Cut depends on the length of the interruption, as described below. If the signal is interrupted for less than 30 seconds, Smart Space replaces the blank portion with a blank space of about three seconds, then continues the recording.

If the signal is interrupted for about 30 seconds, Auto Cut replaces the blank portion with a blank space of about three seconds, then pauses the recording. You can mark track numbers either manually or automatically while recording. By marking track numbers at specific points, you can quickly locate the points later or edit the MD easily.