- Can't find what you're looking for?
- NETGEAR ROUTER (ACCESS SETUP AND QOS)
- Netgear dg834g manual reset limit
- How do I perform a factory reset on my DGN2000 or DG834Gv5 router?
- Need to Contact Support?
- Can’t find what you’re looking for?
- Netgear DG834Gv5 User Manual
- DG834Gv3 – 54 Mbps Wireless ADSL Firewall Modem
Can't find what you're looking for?
The operation of some equipment for example, test transmitters in accordance with the regulations may, however, be subject to certain restrictions. This chapter provides further details about these settings, as well as instructions on how to log in to the modem router for further configuration.
The Smart Wizard will assist you in configuring your wireless settings and enabling wireless security for your network. For help with configuring DHCP, see Change your password: Figure 3. Enter a new password twice, and then click Next.
NETGEAR ROUTER (ACCESS SETUP AND QOS)
Depending on the type of connection, you are prompted to enter your ISP settings, as shown in the following table. You Configuring Your Internet Connection v1.
To view or configure the basic settings: 1. Page 19 5. If no login is required, you can specify the MAC Address setting. Click Apply to save your settings. Click Test to test your Internet connection.
Your ISP automatically assigns these addresses. Your modem router automatically connects to the Internet when one of your computers requires access.
It is not necessary to run a dialer or login application such as dial-up networking or Enternet to connect, log in, or disconnect. To successfully implement wireless security, check each wireless adapter to determine which wireless security option it supports.
Netgear dg834g manual reset limit
WEP connections can take slightly longer to establish. Also, WEP encryption can consume more battery power on a notebook computer. You can allow only trusted PCs to connect so that unknown PCs cannot wirelessly connect to the modem router. Restricting access by MAC Select the region in which the modem router will operate.
How do I perform a factory reset on my DGN2000 or DG834Gv5 router?
For initial configuration and test, leave the other settings unchanged. Enter a character maximum name. This field is case-sensitive.
Wireless network names provide a means for separating traffic for different networks. Enter 26 hexadecimal digits any combination of 0—9, a—f, or A—F. Enter the encryption keys. You can manually or automatically program the four data encryption keys.
Go to the client wireless computer, and run a WPS configuration utility. You can view these settings in the Wireless Settings screen. After WPS is implemented, the modem router automatically selects this check box so that your SSID and wireless security settings remain the same if other WPS-enabled devices are added later.
You can restrict access to only trusted computers so that unknown computers cannot wirelessly connect to the modem router. Adjust the list as needed for your network.
Page Protecting Your Network Note: The user name and password are not the same as a user name or password you might use to log in to your Internet connection.
The ideal password should contain no dictionary words from any language, and should be a mixture of both upper and lower case letters, numbers, and symbols. From the main menu, under the Maintenance heading, select Set Password to display the Set Password screen: Figure 3.
To change the password, first enter the old password, and then enter the new password twice. With its content filtering feature, the modem router prevents objectionable content from reaching your PCs.
Need to Contact Support?
You can control access to Internet content by screening for keywords within Web addresses. Turn on keyword blocking according to the settings on the Schedule screen. To delete a keyword or domain, select it from the list, click Delete Keyword, and then click Apply.
Either select a service from the Inbound Services drop-down list, or select User Defined and create a custom service. No log entries will be made for this service. Any traffic for this service type will be logged. Traffic of this type that matches the rule will be logged.
When you are finished, click Apply. Select whether the traffic will be logged. The choices are: — Never. Use the following procedure to define your own services. To define a service: 1. To localize the time for your log entries, you must specify your time zone: 1. Backing Up, Restoring, or Erasing Your Settings The configuration settings of the modem router are stored in a configuration file in the modem router.
Can’t find what you’re looking for?
If the upgrade file is compressed a. After the upgrade is complete, you might need to restore your configuration settings. To upgrade the modem firmware: 1. Firmware Version This field displays the modem router firmware version.
These are set in Region The country where the unit is set up for use. Connecting to The connection status. Table Description or action The type of event and what action was taken if any. Tip: Be sure to change the modem router default password to a very secure password. Enter a beginning and ending IP address to define the allowed range.
Netgear DG834Gv5 User Manual
Make the changes that you want, and then click Apply to save the settings. This should be used only as a diagnostic tool, since it allows your modem router to be discovered. These features can be found under the Advanced heading in the modem router main menu. Click Apply to save the changes. Reserved IP addresses should be assigned to servers that require permanent IP settings. However, if your Internet account uses a dynamically assigned IP address, you will not know in advance what your IP address will be, and the address can change frequently.
Select the name of your dynamic DNS service provider.
DG834Gv3 – 54 Mbps Wireless ADSL Firewall Modem
The static route would look like Figure The route name is for identification purposes only. Select this check box if you want to limit access to the LAN only. UPnP can be enabled or disabled for automatic device configuration.
The default setting for UPnP is enabled. VPN tunnels also enable access to network resources across the Internet. You can click Back to return to the Summary screen. Click Done on the Summary screen to complete the configuration procedure. The VPN Policies screen displays, showing that the new tunnel is enabled: Figure To view or modify the tunnel settings, select the radio button next to the tunnel entry and click Edit.
Figure A New Connection listing appears in the list of policies. Page 90 Figure My Identity and Security Policy subheadings appear below the connection name.
Figure b. In the Select Certificate drop-down list, select None. In this example, is entered.
This selection must match your selection in the DGG v5 configuration. The Log Viewer screen for a successful connection is shown in the following figure When the connection is successful, the SA changes to the yellow key symbol shown in the previous figure. Page 97 Select VPN Wizard on the main menu.