Page of Go. Page 70 - FContrepoids de la barre de Bell, joints Page 86 Page 87 - Inizializzazione del Giroscopio, Test di Page 92 - Regolazione dell'Allineamento della pala Page 93 - Regolazione dell'Allineamento del palino Page 94 - Pesi della Flybar, Spessori di Ammortizz Table of Contents. Manuel d'utilisation.
Manuale di Istruzioni. For up-to-date product literature, visit www.
E-FLITE Blade SR Instruction Manual
Meaning of Special Language: The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
Page 4: Introduction It comes out of the box programmed to provide softer climb, pitch and roll response around the center of stick movement. This, combined with the tough, two-piece main frame and lower head speed, makes the Blade SR more forgiving and easier to master than most conventional CP helis.
For this reason the initial charge may only take approximately 30—50 minutes. Move the battery forward or rearward as required to achieve a slightly nose down or perfectly level helicopter position. Unplug the three bullet connectors between the main motor and ESC and tail motor from the 2-in-1 control unit.
Page 9 With the stick pulled back down, the swashplate should raise, decreasing the pitch of the main blades. Mode 2 Mode 1 Descend Again viewing the helicopter from the left or right side, move the elevator stick forward and aft to check elevator pitch control.
When the stick is pushed forward, the swashplate should also tilt forward. Page 10 With the stick pulled back, the swashplate will tilt toward the rear. Mode 1 Mode 2 Heli Moves Backward While viewing the helicopter from the rear tail boom toward you , move the aileron stick left and right to check aileron roll control.
When the stick is pushed to the left, the swashplate should also tilt left. Page 11 With the stick pushed right, the swashplate will tilt to the right.
Mode 1 and 2 Heli Moves Right Moving the rudder stick to the left will turn yaw the nose of the helicopter to the left about the axis of the main shaft.
This is accomplished by decreasing the speed of the tail rotor blade. Page 12 These dip switches set the transmitter programming for functions such as servo reversing, model type and various forms of mixing. Each switch should be set in the position as shown for proper control of the Blade SR.
Blade 120 SR RTF and BNF by BLADE Review
Page Gain Adjustments The servo mode selection switch is found on the side of the gyro. You must be certain that the servo mode selection switch on the gyro is set to standard servo mode to ensure proper response and performance of the gyro.
You can check the blade tracking either on the ground or in the air at eye level. It might be a good idea to have an assistant on hand to help sight the blades.
Page Flybar Paddle Tracking Adjustment Typically, not much adjustment should be necessary to properly track the main rotor blades. In most cases, you should be able to get both blades tracking perfectly in the same plane.
Page Channel 5 Knob Note: Because the SmartSafe positions are set during the binding process, it is important to set all channels to the preferred fail- safe positions before proceeding.
Blade 120 SR Heli Advanced Swash Plate Setup and Maiden Flight
In the case of the Blade SR, we strongly recommend setting the throttle stick and throttle trim to their lowest positions, and the rudder, aileron and elevator sticks and trims to their neutral positions. Now you will need to power down the 2-in-1 control unit, receiver and transmitter, and remove the bind plug from the receiver.
Note: You will need to remove the bind plug from the receiver once it has been bound to the transmitter. Page 25 If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product, you are advised to return this Product immediately in new and unused condition to the place of purchase.
Page 27 Materialien. Entnehmen und inspizieren Sie die Bauteile. Page Ladefehler Sender zeigt Ihnen dazu die Spannung an.
Rc heli blade 120 sr manual
Setzen Sie dazu auch bitte die Kabinenhaube auf das Modell. Page 36 Bewegen Sie den Stick nach rechts, sollte sich die Taumelscheibe auch nach rechts bewegen. Mode 1 and 2 Helikopter dreht rechts Bewegen Sie den linken Stick nach links, wird sich die Nase des Helikopters nach links drehen.
Der Blade SR kann Der Sender muss dazu in den Mode Reichweitentest gebracht werden und sendet dann mit verminderter Sendeleistung. Se tale cella non scenda mai sotto i 3 V durante il volo.
RC Helicopters, Multirotors and FPV Drones.
Per questo motivo la carica iniziale potrebbe richiedere soltanto minuti. Page 82 Quando lo stick viene mandato in basso, il piatto ciclico dovrebbe alzarsi, diminuendo il passo delle pale principali.
Quando lo stick viene mandato avanti, anche il piatto ciclico dovrebbe inclinarsi leggermente in avanti. Page 83 Quando lo stick viene mandato indietro, il piatto ciclico dovrebbe inclinarsi leggermente verso la parte posteriore. Page 84 Quando lo stick viene mandato a destra, il piatto ciclico dovrebbe inclinarsi leggermente verso destra.
Blade 120 SR BNF
Page Disinnesco Acceleratore Sebbene sia possibile far volare il Blade SR indoor, consigliamo di farlo solo in uno spazio chiuso dalle dimensioni adeguate, come ad esempio una palestra libera da persone e ostacoli. Solitamente, le regolazioni richieste non sono considerevoli. Page bladehelis. US Patent 7,, The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Spektrum radios and accessories are exclusively available from Horizon Hobby, Inc. Comments to this Manuals Your Name:. Enter text from picture:. Latest comments:. Print page 1 Print document pages.
Cancel Delete. Sign in OR. Don't have an account?
Sign up! Restore password.