Yamaha Raptor 90cc Service Manual

Yamaha raptor 90cc service manual

This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the cookie policy. By closing this banner, you agree to the use of cookies. Page of Go. Table of Contents.

First edition, May All rights reserved. Any reproduction or unauthorized use without the written permission of Yamaha Motor Corporation, U.

Yamaha RAPTOR YFM125RA Service Manual

Printed in U. Page 3 If there is any question about a service procedure, it is imperative that you contact a Yamaha dealer for any service information changes that apply to this model.

This policy is intended to provide the customer with the most satisfaction from his vehicle and to conform to federal environmental quality objectives. Comprehensive explanations of all installation, removal, disassembly, assembly, repair and check procedures are laid out with the individual steps in sequential order.

The following symbols are not relevant to every vehicle. This information will be needed to order spare parts. Page Important Information 5.

Specifications

Keep all parts away from any source of fire. Use oil and grease recommended by Yamaha for all lubrication jobs. Other brands may be similar in function and appearance, but When installing oil seals, lubricate the oil seal lips with a light coat of lithium-soap-based grease.

Oil bearings liberally when installing, if appropriate. Remove: a screwdriver, then pull the fastener out. Reversing the ECA battery lead connections could damage the electrical components.

Never disconnect a battery lead while the engine is running; Use only the appropriate special tools as this will help prevent damage caused by the use of inappropri- ate tools or improvised techniques.

Special tools, part numbers or both may differ depending on the country.

View Yamaha Owner's Manuals Online

Illustration pages Valve spring compressor , YM Valve spring compressor attachment , Valve spring compressor adapter Tightening torque specifications for spe- cial components or assemblies are provided for each chapter of this manual. To avoid warpage, tighten multi-fastener assemblies in a crisscross pattern and progressive stages until the specified tightening torque is reached. Apply Yamaha bond No. Lubricate the contact surfaces of the cylinder head bolts and on both contact surfaces of wash- ers with engine oil.

Oil pan 2. Oil strainer 3. Oil pump 4. Rotary filter 5.

03 08 Yamaha Raptor 80 Service Manual YFM80 PDF Download and Owners Manual YFM80 ATV Workshop manual

Cylinder head 6. Camshaft 7.

Yamaha raptor 90cc service manual

Crankshaft 8. Drive axle 9.

Culture s consequences pdf viewer

Main axle Camshaft 2. Rotary filter 3.

Yamaha raptor 90cc service manual

Oil strainer 5. Push lever shaft Crankshaft 4. Main axle 5. Drive axle Brake hose 2. Throttle cable 3. Plastic band 4.

2009-2013 Eton Yamaha raptor 90 service manual

Parking brake cable 5. Clutch cable A. Pass the brake hose and throttle cable through the guide of the handlebar protec- tor.

Ley 227 06 pdf download

Pass the throttle cable behind the brake hose. Neutral indicator light lead 2. Front brake light switch lead 3.

Yamaha raptor 90cc service manual

Main switch lead 4. Headlight lead 5. Brake hose 6. Starter motor lead 7. Battery negative lead 8. Parking brake cable 9.

Troubleshooting

Rear brake light switch lead Carburetor warmer lead Air vent hose Crankcase breather hose Rear brake reservoir 2. Rear brake light switch 3.

Yamaha raptor 90cc service manual

Clip 4. Rear brake reservoir hose 5. Rear brake master cylinder 6. Parking brake cable 7. Parking brake cable adjusting nut 8.

DOWNLOAD Yamaha Raptor Repair Manual 50 80 90 250 350 660 700

Brake hose 9. Rear brake caliper Swingarm A. Spring 2. Adjusting screw 3. Washer 4. Adjusting nut 5.

Clutch switch lead 7. Handlebar switch lead 8.

Ay 3 8910 pdf writer

Wire harness Neutral switch lead Drain hose Clamp Screw Collar Headlight Spring nut Headlight stay Frame Damper plate A. Air vent hose 2. Clamp 3. Starter motor lead 4. AC magneto lead 5. Carburetor overflow hose 6. Frame 7. Seat pad 8. Wire harness 9.